當前位置 > 產品目錄 > 試劑 > 免疫學/診斷檢測試劑 > Gα13活性檢測試劑盒

Gα13活性檢測試劑盒

英文名稱：	Gα13 Pull-Down Activation Assay Kit	總訪問：	336
國產/進口：	進口	半年訪問：	35
產地/品牌：	NewEast Biosciences	產品類別：	免疫學/診斷檢測試劑
規 格：	Gα13	最后更新：	2023-5-11
貨號：	80401
CAS 號：
參考報價：
立即詢價 電話咨詢

[發表評論] [本類其他產品] [本類其他供應商] [收藏]

分享：微信新浪微博

銷售商：武漢費斯德生物科技有限公司

查看該公司所有產品 >>

產品介紹
公司簡介

** 本公司銷售的所有產品僅供實驗科研使用，不用于人體及臨床診斷
產品說明：https://www.nebio.com.cn/product/ga13-pull_down/

Gα13 Pull-Down Activation Assay Kit

Cat. # 80401

Introduction
A. Background

A structurally diverse repertoire of ligands, from photons to large peptides, activates GPCRs to elicit their physiological functions. Ligand-bound GPCRs, in turn, function as guanine nucleotide exchange factors catalyzing the exchange of GDP bound on the Gα subunit with GTP in the presence of Gβγ, causing the dissociation of the Gα subunit from the Gβγ dime to form two functional units (Gα and Gβγ). Both Gα and Gβγ subunits signal to various cellular signaling pathways. Based on the sequence and functional homologies, G proteins are grouped into four families: Gs, Gi, GGq, and G12. As increasing numbers of effectors and interacting proteins for these G proteins have been identified, the physiological processes in which G proteins participate are multiplying.

Among the four subfamilies of G proteins, the function of G12/13 subfamily is less well understood. In this family, there are two members, G12 and G13, that are expressed ubiquitously. Gα12 knockout mice appeared normal. Gα13 knockout mice displayed embryonic lethality (~E9.5). The Gα13-/- mouse embryos had defective vascular systems. G13 is also essential for receptor tyrosine kinase-induced migration of fibroblast and endothelial cells.

B. Assay Principle

The Gα13 Activation Assay Kit uses configuration-specific anti-Gα13-GTP Mouse monoclonal antibody to measure Gα13-GTP levels in cell extracts or in vitro GTPγS loading Gα13 activation assays. Anti-Gα13-GTP mouse monoclonal antibody is first incubated with cell lysates containing Gα13-GTP. Next, the GTP-bound Gα13 is pulled down by protein A/G agarose. Finally, the precipitated Gα13-GTP is detected through immunoblot analysis using anti-Gα13 mouse monoclonal antibody.

C. Kit Components

1. Anti-Gα13-GTP Mouse Monoclonal Antibody (Cat. # 26902): One vial – 35 µL (1 mg/ml) in PBS, pH 7.4, containing 50% glycerol. This antibody specifically recognizes Gα13-GTP from all vertebrates.

2. Protein A/G Agarose (Cat. # 30301): One vial – 600 µL of 50% slurry.

3. 5X Assay/Lysis Buffer (Cat. # 30302): One bottle – 30 mL of 250 mM Tris-HCl, pH 8, 750mM NaCl, 50 mM MgCl2, 5 mM EDTA, 5% Triton X-100.

4. Anti-Gα13 Mouse monoclonal Antibody (Cat. # 21005): One vial – 50 µL (1mg/mL) in PBS, pH 7.4, contained 50% glycerol.

5. 100X GTPγS (Cat. # 30303): One vial – 50 µl at 10 mM, use 5 µL of GTPγS for GTP-labeling of 0.5 mL of cell lysate.

6. 100X GDP (Cat. # 30304): One vial – 50 µl at 100 mM, use 5 µL of GDP for GDP-labeling of 0.5 mL of cell lysate.

7. HRP-Goat Anti-Rabbit IgG (Cat. #29002): 50 µL (0.4 mg/mL) in PBS, pH 7.4, contained 50% glycerol.

D. Materials Needed but Not Supplied

1. Stimulated and non-stimulated cell lysates

2. Protease inhibitors

3. 4°C tube rocker or shaker

4. 0.5 M EDTA at pH 8.0

5. 1.0 M MgCl2

6. 2X reducing SDS-PAGE sample buffer

7. Electrophoresis and immunoblotting systems

8. Immunoblotting wash buffer such as TBST (10 mM Tris-HCl, pH 7.4, 0.15 M NaCl, 0.05% Tween-20)

9. Immunoblotting blocking buffer (TBST containing 5% Non-fat Dry Milk or 3% BSA)

10. ECL Detection Reagents

E. Example Results

The following figure demonstrates example results seen with the Gα13 Activation Assay Kit. For reference only.

Gα13 Activation Assay. MEF cells were treated with (lane 2) or without (lane 1) LPA. Cell lysates were incubated with an anti-Gα13-GTP monoclonal antibody (Cat. # 26902) (top panel). The precipitated active Gα13 was immunoblotted with an anti-Gα13 rabbit polyclonal antibody (Cat. # 21005). The bottom panel shows the Western blot with anti-Gα13 of the cell lysates used (5% of that used in the top panel).
Assay Procedure
A. Reagent Preparation
1X Assay/Lysis Buffer: Mix the 5X Stock (Cat. # 30301) briefly and dilute to 1X in deionized water. Just prior to usage, add protease inhibitors such as 1 mM PMSF, 10 µg/mL leupeptin, or 10 µg/mL aprotinin.
B. Sample Preparation
Adherent Cells

1. Culture cells (one 10-cm plate, ~107 cells) to approximately 80-90% confluence. Stimulate the cells with activator or inhibitor as desired.

2. Aspirate the culture media and wash twice with ice-cold PBS.

3. Completely remove the final PBS wash and add ice-cold 1X Assay/Lysis Buffer (See Reagent Preparation) to the cells (0.5-1 mL per 10 cm tissue culture plate).

4. Place the culture plates on ice for 10-20 minutes.

5. Detach the cells from the plates by scraping with a cell scraper.

6. Transfer the lysates to appropriate size tubes and place on ice.

7. If nuclear lysis occurs, the cell lysates may become viscous and difficult to pipette. If this occurs, lysates can be passed through a 27½-gauge syringe needle 3-4 times to shear the genomic DNA.

8. Clear the lysates by centrifuging at 12,000 x g and 4°C for 10 minutes.

9. Collect the supernatant and store the sample (~1-2 mg of total protein) on ice for immediate use, or snap freeze and store at -70°C for future use.

Adherent Cells

1. Culture cells and stimulate with activator or inhibitor as desired.

2. Perform a cell count and then pellet the cells through centrifugation.

3. Aspirate the culture media and wash twice with ice-cold PBS.

4. Completely remove the final PBS wash and add ice-cold 1X Assay/Lysis Buffer (See Reagent Preparation) to the cell pellet (0.5-1 mL per 107 cells).

5. Lyse the cells by repeated pipetting.

6. Transfer the lysates to appropriate size tubes and place them on ice.

7. If nuclear lysis occurs, the cell lysates may become viscous and difficult to pipette. If this occurs, lysates can be passed through a 27½-gauge syringe needle 3-4 times to shear the genomic DNA.

8. Clear the lysates by centrifuging at 12,000 x g and 4°C for 10 minutes.

9. Collect the supernatant and store sample on ice for immediate use, or snap freeze and store at -70°C for future use.

C. In vitro GTPγS/GDP Protein for Positive and Negative controls

Note: In vivo stimulation of cells will activate approximately 10% of the available Gα13, whereas in vitro GTPγS protein loading will activate nearly 90% of Gα13.

1. Aliquot 0.5 mL of cell extract (or 1 µg of purified Gα13 protein) into two microcentrifuge tubes.

2. To each tube, add 20 µL of 0.5 M EDTA (final concentration of 20 mM).

3. Positive control: add 5 µL of 100 X GTPγS (Cat. # 30302) to the 1st tube

4. Negative control: add 5 µL of 100 X GDP (Cat. # 30304) to the 2nd tube.

5. Incubate both tubes at 30°C for 30 minutes with agitation.

6. Stop loading by placing the tubes on ice and adding 32.5 µL of 1 M MgCl2 (final concentration of 60 mM).

D. Affinity Precipitation of Activated G Protein

1. Aliquot 0.5-1 mL of cell lysates (about 1 mg of total cellular protein) to a microcentrifuge tube.

2. Adjust the volume to 1 mL with 1X Assay/Lysis Buffer (See Reagent Preparation).

3. Add 1 µL anti-Gα13-GTP antibody (Cat. # 26902).

4. Prepare the protein A/G Agarose bead slurry (Cat. # 30301) by resuspending through vertexing or titrating.

5. Quickly add 20 µL of resuspended bead slurry to above tube.

6. Incubate the tube at 4°C for 1 hour with gentle agitation.

7. Pellet the beads through centrifugation at 5,000 x g for 1 min.

8. Aspirate and discard the supernatant (making sure not to disturb or remove the bead pellet.

9. Wash the beads 3 times with 0.5 mL of 1X Assay/Lysis Buffer, centrifuging and aspirating each time.

10. After the third wash, pellet the beads through centrifugation and carefully remove all the supernatant.

11. Resuspend the bead pellet in 20 µL of 2X reducing SDS- PAGE sample buffer.

12. Boil the sample for 5 minutes.

13. Centrifuge it at 5,000 x g for 10 seconds.

E. Western Blot Analysis

1. Load 15 µL/well of pull-down supernatant to a polyacrylamide gel (17%). It is recommended to include a pre-stained MW standard (as an indicator of a successful transfer in step 3 below).

2. Perform SDS-PAGE following the manufacturer’s instructions.

3. Transfer the gel proteins to a PVDF or nitrocellulose membrane following the manufacturer’s instructions.

Note: Steps 4-11 are at room temperature with agitation

4. Following electroblotting, immerse the PVDF membrane in 100% Methanol for 15 seconds, and then allow it to dry at room temperature for 5 minutes.

Note: If Nitrocellulose is used instead of PVDF, step 4 Should be skipped.

5. Block the membrane with 5% non-fat dry milk or 3% BSA in TBST for 1 he at room temperature with constant agitation.

6. Wash the blotted membrane three times with TBST, 5 minutes each time.

7. Incubate the membrane with anti-Gα13 Mouse Monoclonal Antibody (Cat. # 21005), which has been freshly diluted 1: 50~500 (depending on the amount of Gα13 proteins in your sample) in 5% non-fat dry milk or 3% BSA in TBST, for 1-2 her at room temperature with constant agitation or at 4°C overnight.

8. Wash the blotted membrane three times with TBST, 5 minutes each time.

9. Incubate the membrane with a secondary antibody (Cat. # 29002), which has been freshly diluted 1: 1000 in 5% non-fat dry milk or 3% BSA in TBST, for 1 he at room temperature with constant agitation.

10. Wash the blotted membrane three times with TBST, 5 minutes each time.

11. Use the detection method of your choice such as ECL.

武漢費斯德生物科技有限公司是美國NewEast Biosciences在中國的辦事處，也是目前國內唯一經銷處。品牌正品現貨供應，交付快，高質量抗體和靈敏高試劑盒，產品折扣大，歡迎咨詢。
目前客戶使用產品發表超過1000谷歌學術文獻，其中論文分布排名前50刊物上。
NewEast Biosciences 在十二年前率先研發倆種獨特的抗體。這倆種抗體僅僅識別活性的GTP酶或者突變的Oncogene。 GTP酶涉及(1)響應細胞表面受體激活的信號轉導，包括跨膜受體，例如介導味覺、嗅覺和視覺的那些，（2）核糖體的蛋白質生物合成，（3）調節細胞分化、增殖、分裂和運動，（4）蛋白質通過膜的易位，（5）細胞內囊泡的運輸，以及囊泡介導的分泌和攝取，通過GTP酶控制囊泡外殼組裝。Oncogene側是誘發癌癥的基因。
更多產品類目和技術資料可查看：武漢費斯德生物官網。

武漢費斯德生物科技有限公司將向你提供以下，抗體或者試劑盒: (1) 僅識別 GTP酶的活性構型的產品, 它可以讓你能夠量化GTP酶在細胞中的活性和分布。(2) 識別突變 Oncogene蛋白, 但不認識相應野生型的抗體。 (3) 對 cAMP 和 cGMP 具有超親和力（無需乙酰化）ELISA檢測試劑盒。

注：2021年武漢費斯德生物科技有限公司和NewEast Biosciences收購了武漢紐斯特生物技術有限公司所有的產品和細胞株。因此, 紐斯特不再擁有這些產品銷售權。如果您在 2022 年 6 月 1 日之后從紐斯特購買相同的產品, 你不應該在你的論文中引用紐斯特的產品為NewEast Biosciences產品。否則，NewEast Biosciences 會去找出版商對你的引用提出異議。請注意, 用國際供應商的產品將會增加您發表文章citation的數量。
選擇正品費斯德經銷處，為您實驗和相關文章提供保障，售后服務到位，產品現貨供應。
** 本公司銷售的所有產品僅供實驗科研使用，不用于人體及臨床診斷。

售后服務

美國NewEast Biosciences品牌國內總經銷處，購買正品品牌產品，質量保證，為您的實驗和科研成果負責
僅供科研使用，如有單位或個人將本公司銷售產品用于臨床診斷、治療等國家專門規定的或企業自行規定的特殊用途，本公司概不承擔任何責任。
如使用過程中發現確屬于產品本身質量問題，請?jiān)谑盏截浐蟮?0天內告知我們并提供真實的書面報告，我們會及時的幫您解決，逾期不再受理，視為合格！所有形式的賠償和退換僅限于產品本身，不涉及任何其他

相關視頻

資料下載

快速詢價 請 登錄或注冊在線詢價　(請留下您的聯系方式，以便供應商聯系您)

* 姓　名：		* 地　區：
* 單　位：		職　位：
* 手機/電話：		* E-mail：
請寄產品資料：	需要不需要	請報價格：	需要報價 不需要報價
留　言：
驗證碼：	換一張
	我希望獲得多家供應商報價